Trümmelbach : un nouveau grand
Anchor test in Trümmelbach.
I took two very rusty anchors from Trümmelbach and replaced them with new, stainless steel one.
After that I took the two old anchors (plate + Maillon Rapide) to our Mammut laboratory for breaking strength testing.
They were still ok and had a breaking strength of 23kN.
After 10 years or more in the water the breaking strength is still ok despite they do not look very trustworthy.
If someone else has old anchors used in canyons and would like to know the breaking strength; Just send them to me:
Matthias Holzinger
Mammut Sports Group AG
5703 Seon
Switzerland
I took two very rusty anchors from Trümmelbach and replaced them with new, stainless steel one.
After that I took the two old anchors (plate + Maillon Rapide) to our Mammut laboratory for breaking strength testing.
They were still ok and had a breaking strength of 23kN.
After 10 years or more in the water the breaking strength is still ok despite they do not look very trustworthy.
If someone else has old anchors used in canyons and would like to know the breaking strength; Just send them to me:
Matthias Holzinger
Mammut Sports Group AG
5703 Seon
Switzerland
Allez Hop!.....
C'est super tes mesures. Ca me rassure de mettre pendu dessus
Faut pas non plus avoir trop confiance. Je me rappelles des spits dans les étages en particuliers qui se cassaient en deux à la simple traction à la main (J'ai pas vérifier s'il y avait 2 alliages différents)
Faut pas non plus avoir trop confiance. Je me rappelles des spits dans les étages en particuliers qui se cassaient en deux à la simple traction à la main (J'ai pas vérifier s'il y avait 2 alliages différents)
Quoi qu'il en soit, on finira tous un jour dans un lit
Here some photos:bernotom a écrit :Interesting your anchor testing, it is a good idea to test the breaking strength of old equipment we find in the canyon.
It was a Ø10mm bolt not stainless? and what was the Maillon Rapide diameter?
Anchor and Maillon was alloy steel and the plate was stainless steel.
The Anchor was M10 and the Maillon Ø8mm.
Dernière modification par holzi le mar. 15 nov. 2011 14:07, modifié 1 fois.
Allez Hop!.....
- Laurinette
- Messages : 1073
- Inscription : lun. 20 juin 2005 10:29
- Localisation : A droite à gauche
- Contact :
Jep you are absolutely rightLaurinette a écrit :but they don't look SO old! I've seen much much worse!
But you know it is bad light in the Trümmelbach and they looked worse than they actually were.
It was still worth testing them .
Dernière modification par holzi le mar. 15 nov. 2011 14:35, modifié 1 fois.
Allez Hop!.....
- fiumicicoli
- Messages : 2809
- Inscription : mer. 29 sept. 2004 14:22
- Localisation : Nancy
- Contact :
The weakest point was most probably rather the bond between the stone and the bolt, which is quite difficult to test on place
--- In Openbach we trust --- http://www.openbach.com
- Laurinette
- Messages : 1073
- Inscription : lun. 20 juin 2005 10:29
- Localisation : A droite à gauche
- Contact :
Yes most likely. As the anchors were also in alloy steel.fiumicicoli a écrit :The weakest point was most probably rather the bond between the stone and the bolt, which is quite difficult to test on place
But I don't have the tools to test them on place.
The material mix alloy/stainless steel or alu/steel is not recommendet.
Allez Hop!.....
D'ailleurs le le Maillon rapide en acier est pas mal rouillé !
Dernière modification par Caracal le mar. 15 nov. 2011 21:53, modifié 1 fois.
Quoi qu'il en soit, on finira tous un jour dans un lit
Ces ammerages sont un peu vieux
Dernière modification par holzi le mer. 16 nov. 2011 14:40, modifié 1 fois.
Allez Hop!.....
- Laurinette
- Messages : 1073
- Inscription : lun. 20 juin 2005 10:29
- Localisation : A droite à gauche
- Contact :
- fiumicicoli
- Messages : 2809
- Inscription : mer. 29 sept. 2004 14:22
- Localisation : Nancy
- Contact :
moi je trouve pasholzi a écrit :Ces amarrages sont un peu vieux
--- In Openbach we trust --- http://www.openbach.com
Le photo n'est pas fait en Suisse.
Effectivement c'est en France, la Reunion, Dudu
Mais il'ya aussi des viex cordes en Tessin. Froda, Lodrino, Pontirone.....mais pas facile de trouve.
Effectivement c'est en France, la Reunion, Dudu
Mais il'ya aussi des viex cordes en Tessin. Froda, Lodrino, Pontirone.....mais pas facile de trouve.
Dernière modification par holzi le mer. 16 nov. 2011 21:21, modifié 1 fois.
Allez Hop!.....
-
- Messages : 7
- Inscription : sam. 07 nov. 2009 13:46
- Localisation : Wettingen/Zürich
- Contact :
Trümmelbach on Saturday, 24. March 2012 at 17.00
Some pics: http://canyon.li/WP/?p=1474
Visitors area is closed until april.
Skiing was easy this day
Some pics: http://canyon.li/WP/?p=1474
Visitors area is closed until april.
Skiing was easy this day
- fiumicicoli
- Messages : 2809
- Inscription : mer. 29 sept. 2004 14:22
- Localisation : Nancy
- Contact :
"Gros débit" I would say
quite dangerous in that period owing to erratic snow melt.
But possible, still...
one or two weeks ago would have been better ?
quite dangerous in that period owing to erratic snow melt.
But possible, still...
one or two weeks ago would have been better ?
--- In Openbach we trust --- http://www.openbach.com
Dernière modification par EmmaZ le jeu. 20 sept. 2012 16:53, modifié 1 fois.
Le sommet est à mi pente.
J’ai lu ca à midi, il a du atterrir en amont de la partie canyon.EmmaZ a écrit : http://www.20min.ch/ro/news/faits_diver ... n-27727408
Ca doit être frustant quand on apercoit l'hélicoptaire une 15aine de fois!!
Dernière modification par bernotom le jeu. 20 sept. 2012 16:58, modifié 1 fois.